I have pulled the kernel from android.git.kernel.org and enabled everything to do with KGDB including kgdbts testing using menuconfig. Successfully built the kernel and flashed it to the device (which is unlocked rooted and running CyanogenMod 7)
I have also followed the instructions found on http://bootloader.wikidot.com/android:kgdb to enable the usb connection to act as a serial connection as required by kgdb (and tested communications from ttyACM0 to ttyGS0 successfully).
The following folders exist indicating that kgdboc and kgdbts have been built into the kernel:/sys/modules/kgdboc/parameters
/sys/modules/kgdbts/parameters
The following is the output from dmesg showing the kgdbts testing being done show what (I think) is a successful completion of the tests:# dmesg | grep kgdb
<6>[ 12.974060] kgdb: Registered I/O driver kgdbts.
<6>[ 12.981781] kgdbts:RUN plant and detach test
<6>[ 12.995178] kgdbts:RUN sw breakpoint test
<6>[ 13.002441] kgdbts:RUN bad memory access test
<6>[ 13.010864] kgdbts:RUN singlestep test 1000 iterations
<6>[ 13.019042] kgdbts:RUN singlestep [0/1000]
<6>[ 13.077850] kgdbts:RUN singlestep [100/1000]
<6>[ 13.132720] kgdbts:RUN singlestep [200/1000]
<6>[ 13.187500] kgdbts:RUN singlestep [300/1000]
<6>[ 13.242370] kgdbts:RUN singlestep [400/1000]
<6>[ 13.297149] kgdbts:RUN singlestep [500/1000]
<6>[ 13.351928] kgdbts:RUN singlestep [600/1000]
<6>[ 13.406829] kgdbts:RUN singlestep [700/1000]
<6>[ 13.461578] kgdbts:RUN singlestep [800/1000]
<6>[ 13.516540] kgdbts:RUN singlestep [900/1000]
<6>[ 13.570922] kgdbts:RUN do_fork for 100 breakpoints
<6>[ 21.117645] kgdb: Unregistered I/O driver kgdbts, debugger disabled.
I believe that the problem I am running into is getting the kernel to trigger kgdb.# echo -n g > /proc/sysrq-trigger
Just results in dropping me back to the command prompt and (I think) it is suppose to freeze everything and send a prompt over usb which is being used as a psuedo serial port since the phone doesn't have a real one.
From what I gather from my research that prompt is supposed to be the trigger that will allow me to issue(gdb) target remote /dev/ttyACM0
And connect to a debugging session with the kernel.
I have also tested /proc/sysrg-trigger with 'b' and 'c' just confirm that I am able to pass some commands to sysrq.
So my question following my long winded attempt to provide as much information as possible is what is 'g' not triggering the debugger?
This is my first attempt at kernel debugging on any system and I have run out of ways to phrase my search on google so I turn to you.
(I have also tried putting kdgbwait in the kernel command line without success as I believe that this is not yet supported by the android kernel)
<6>[ 12.981781] kgdbts:RUN plant and detach test
<6>[ 12.995178] kgdbts:RUN sw breakpoint test
<6>[ 13.002441] kgdbts:RUN bad memory access test
<6>[ 13.010864] kgdbts:RUN singlestep test 1000 iterations
<6>[ 13.019042] kgdbts:RUN singlestep [0/1000]
<6>[ 13.077850] kgdbts:RUN singlestep [100/1000]
<6>[ 13.132720] kgdbts:RUN singlestep [200/1000]
<6>[ 13.187500] kgdbts:RUN singlestep [300/1000]
<6>[ 13.242370] kgdbts:RUN singlestep [400/1000]
<6>[ 13.297149] kgdbts:RUN singlestep [500/1000]
<6>[ 13.351928] kgdbts:RUN singlestep [600/1000]
<6>[ 13.406829] kgdbts:RUN singlestep [700/1000]
<6>[ 13.461578] kgdbts:RUN singlestep [800/1000]
<6>[ 13.516540] kgdbts:RUN singlestep [900/1000]
<6>[ 13.570922] kgdbts:RUN do_fork for 100 breakpoints
<6>[ 21.117645] kgdb: Unregistered I/O driver kgdbts, debugger disabled.
I believe that the problem I am running into is getting the kernel to trigger kgdb.# echo -n g > /proc/sysrq-trigger
Just results in dropping me back to the command prompt and (I think) it is suppose to freeze everything and send a prompt over usb which is being used as a psuedo serial port since the phone doesn't have a real one.
From what I gather from my research that prompt is supposed to be the trigger that will allow me to issue(gdb) target remote /dev/ttyACM0
And connect to a debugging session with the kernel.
I have also tested /proc/sysrg-trigger with 'b' and 'c' just confirm that I am able to pass some commands to sysrq.
So my question following my long winded attempt to provide as much information as possible is what is 'g' not triggering the debugger?
This is my first attempt at kernel debugging on any system and I have run out of ways to phrase my search on google so I turn to you.
(I have also tried putting kdgbwait in the kernel command line without success as I believe that this is not yet supported by the android kernel)
